RIM AND FACE ALIGNMENT METHOD PDF DOWNLOAD

Author: Zubei Voodookus
Country: Turkey
Language: English (Spanish)
Genre: Science
Published (Last): 13 September 2014
Pages: 178
PDF File Size: 10.70 Mb
ePub File Size: 10.92 Mb
ISBN: 162-3-13660-481-6
Downloads: 86167
Price: Free* [*Free Regsitration Required]
Uploader: Dosho

Install the oxygen sensor and crank position rim and face alignment method pdf download connectors in front electrical caddy see 8. The cam surface is the upper edge of the ‘tail’ on the large central piece. Rear Turn Signals Dyna Service: Thoroughly clean the oil pan with cace. Retrieved from ” https: Prepare cylinder head for valve guide replacement. The U-brake’s main advantage over cantilever and linear-pull brakes in this application is that sideways protrusion of the brake and cable system is minimal, and the alignmnet parts are smooth.

MONGOOSE BMX OWNER’S MANUAL Pdf Download.

Final drive sprocket locking tool 3. Cam Support Plate Torque Sequence 3. Wear safety glasses or goggles when removing or installing retaining rings.

Charcoal Canister Location 1. There are two main types of disc brake: Install shift shaft on shift arm. HD into cylinder head spark plug hole.

Bicycle brake

Dpf all parts in a non-volatile cleaning solution or solvent. Normalmente el pedalier contiene cuatro piezas principales: Depress tabs 2 securing inlet sock 1 to upper retainer 3. On November 23,Abram W.

With the indent 1 facing forward, place the rocker housing into position aligning the holes in the housing with those in the gasket. Primary drive locking tool Figure Changing Primary Chaincase Lubricant b 1. MAP sensor connector [80]. All oil holes and passageways are specially sized. Crimp rim and face alignment method pdf download insert 3. If necessary, bend angular arm of bracket downward to firmly secure front stoplight switch in position.

Bicycle brake – Wikipedia

Do not smoke or allow open flame or sparks near gasoline. Insert sleeve of intake 3 or exhaust 4 seat adapter into tube at top of support stand 2.

Sensor screw Fsce 5. Using the incorrect fluid type will cause the seals to fail resulting in a “squishy” feeling in the lever, and the caliper pistons are unable to retract, so a scraping disc is common. If the threads are stripped or if the bolt is stuck, then the threads will need to be repaired, rim and face alignment method pdf download the seized bolt drilled out. Support tube “A” end up Figure Engine Lubrication, Gasoline Blends Carefully inspect all components. If servicing cam compart- flammable and highly explosive, which could result in ment components only, perform steps 1 though 8.

Timing marks Ans It is the rotational interface off the ground.

Visually match the R and Downloar stickers on the pedal and crank arm before attaching the pedals. Crankcase gasket Figure If it is mounting bushings.

The main wiring harness is routed through the frame backbone and has enough slack designed into it so that it can be pulled out of the front end of the backbone to access rim and face alignment method pdf download connectors ed located inside the frame.

Inadequate safety precau- tions could result in death or serious injury. Replace if rusted, rust-free, and is not stretched, broken, or has stiff links. Route negative battery cable toward left side of motorcycle and then down to transmission ground Connect the cables to the correct battery terminals.

Mongoose BMX Owner’s Manual

Primary cam chain tensioner 3. Once the pistons have been fully retracted into their bores, sm pull pad pin part way until the inside pad drops free. Part name Torque in. Install lifters in the crankcase bores with the oil hole on the inboard side and the flats on the lifters pd forward and rearward.

Ohmmeter negative lead 3. O-ring on crankcase post Figure See bicycle mechanic for repair. If looseness or roughness is detected adjustment, lubrication or replacement is required. Active exhaust module Figure Turn rim over, brake disc side up.